DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither Rainier Arms LLC, nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components. For additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and parts visit www.glock.com.
Only 3 left
Strike Industries Modular Guide Rod for Glock Gen 3 - Red
The SI Modular Guide Rod for Glock Gen 3 is a stainless steel, customizable system that accepts any aftermarket Glock Spring as well as Strike Industries’ custom recoil spring weights. Its stainless steel shaft and anodized aluminum end cap will not rust, crack or break as easily as polymer rods found in oem Glock pistols, increasing it’s service life compared to standard recoil assemblies. Fine tune your Glock’s recoil characteristics and improve reliability by using Strike Industries recoil springs for Glock offered in various weights without having to buy more than one guide rod. Simply unscrew the endcap, replace the spring to your preference, replace the end cap and you’re good to go!
SI also offers the end caps in various colors and designs to add a custom look and more personalization to your pistol.
Product Specifications:
Shaft ID: 0.223”
OD: 0.41”
Length: 3.10” (without shims)
Contents:
1x GMGR : SUS303
3x endcaps: 7075 T6 Aluminum
2x 0.2mm shims: SUS304
1x 0.4mm shims: SUS304
Instructions: The varieties of included shims are to ensure the guide rod fits a wide variety of Glock slides. Begin with just the 0.4mm shim and test for fit and function. the shims also change how flush the end cap is to the front of the slide.
Compatibility: G17,17L,22,24,31,34,35,37
Features:
Easily swap different spring weights.
Made from 303 Stainless Steel for corrosion resistance and increased toughness.
Adjustable fit with the included shims even allows compatibility with our Jitterplug Glock Gen 3 upgrade.
Endcaps available in 4 different colors, and 3 different designs.
NOTE: Very light reduced power springs may not function 100% in stock platforms when feeding from reduced capacity magazines.
NOTE: Use of medium strength thread locker to the endcap threads during installation is highly recommended.
DISCLAIMER: This product is not manufactured, authorized, endorsed, or warranted by GLOCK. GLOCK does not warrant or represent that this product is compatible with GLOCK pistols.
Review by Benson W. on 22 Jan 2018review stating Rods Look Good & Work
I have only shot 200 rounds with SI Modular Guide Rod and it works fine I have tried different springs with the unit including Is 11-13-15 gauge but the stock Glock Gen 3 spring works the best with the SI Rod, it will take many more rounds to be more specific but I like it I also installed it on my Glock 22 and tried different springs but once aga...Read MoreRead more about I have only shot 200 rounds with SI
in I like it best with the SI Rod and Glock OEM spring combo with my Glock 22 but of course I did not shoot many rounds do to the time frame. Read LessRead less about I have only shot 200 rounds with SI
Review by gino a. on 11 Jan 2018review stating Needs work
The step from the rod to the end fitting hits the slide during travel and marked the slide. I have not fired it, this has happened during function testing. The red has also worn off on the edge that’s making contact. I feel like the whole length of the rod and fitting should be the same diameter without the step.
Review by Benson W. on 22 Jan 2018review stating Rods Look Good & Work
I have only shot 200 rounds with SI Modular Guide Rod and it works fine I have tried different springs with the unit including Is 11-13-15 gauge but the stock Glock Gen 3 spring works the best with the SI Rod, it will take many more rounds to be more specific but I like it I also installed it on my Glock 22 and tried different springs but once aga...Read MoreRead more about I have only shot 200 rounds with SI
in I like it best with the SI Rod and Glock OEM spring combo with my Glock 22 but of course I did not shoot many rounds do to the time frame. Read LessRead less about I have only shot 200 rounds with SI
Review by gino a. on 11 Jan 2018review stating Needs work
The step from the rod to the end fitting hits the slide during travel and marked the slide. I have not fired it, this has happened during function testing. The red has also worn off on the edge that’s making contact. I feel like the whole length of the rod and fitting should be the same diameter without the step.
